Bracket (PVC) brown System 90

Bracket (PVC) brown System 90
 

The BRYZA GUTTER SYSTEM is an established product that was introduced to the market in early 2004.
BRYZA is a complete system, consisting of gutters with a semicircular cross-section of 75, 100, and 125,
a group of fittings, and downpipes with two diameters of 63 and 90mm.
The discreet elegance of classic shapes, easy installation, and a choice
of two colors in various sizes fulfill all customer wishes.

         Brown (RAL 8017)              -              Graphite (RAL 7021)

75 System
 

Gutter 75mm with downpipe 63mm.
For small residential buildings, canopies, garages,
balconies, and attics.
 

100 System
 

Gutter 100mm with downpipe 90 or 63mm.
Single-family houses, small and medium-sized warehouses,
commercial and industrial buildings, and 
public buildings.
 

125 System
 

Gutter 125mm with downpipe 90mm.
Single and multi-family houses, apartment blocks,
warehouses, public buildings, commercial
and industrial buildings.
 

Gutter System Parts
 

1.    "Gutter" 75, 100, 125mm; 2m
2.    "Gutter bracket" 75, 100, 125mm
3.    "Inside corner 90°" 75, 100, 125mm
4.    "Gutter connector" 75, 100, 125mm
5.    "Outside corner 90°" 75, 100, 125mm
6.    "Outlet" 75/63, 100/63, 100/90, 125/90mm
7.    "Gutter end cap right/left" 75, 100, 125mm
8.    "Downpipe" 63, 90mm
9.    "T-piece" 63, 90mm
10.  "Bracket (PVC)" 63, 90mm
11.  "Downpipe connector/coupling" 63, 90mm
12.  "Reduction" 90/63mm
13.  "Bend 67.5°" 63, 90mm
14.  "Adjustable gutter iron (metal)" 75, 125mm
15.  "Hook for PVC bracket" 120, 160, 180, 220, 250, 350mm
16.  "Inside corner adjustable angle 120° to 145°" 125mm
17.  "Outside corner adjustable angle 120° to 145°" 75, 100, 125mm
 

Connection Type
 

The gutters are connected to the pipe fittings through a snap connection.
The connection is sealed with a rubber profile located in the groove of a pipe fitting.
This type of connection allows for easy installation and ensures the required
tightness. The connection of the downpipes with the pipe fittings is done with the connection
couplings without sealing. The mentioned connection types allow for thermal length changes
of the gutter system parts to be compensated.
 

Please note during installation!
 

The PVC and steel brackets are mounted directly on the roof battens or rafters. 
The bracket spacing should be 40-50cm. For proper water drainage, the
gutter should have a slope of 2mm per 1m towards the outlet.

Cutting the Gutters and Downpipes
 

Cut the gutter or downpipe to the correct length with a fine-toothed saw at a right angle.

Gutter Installation in the Brackets and Installation of Outlets and Parts 
 

The installation in the PVC and metal brackets begins with inserting the
gutter bead into the front nose of the bracket, then pressing the inner part of the gutter
under the rear nose.
Corner piece, outlet, and gutter connector are mounted by sliding
onto the front gutter bead and then snapping into the rear gutter bead.
When connecting, pay attention to the correct position of seals in outlets, connectors,
and corner pieces, as well as to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets on the gutter connectors, outlets, and 
corner pieces.

Corner piece, outlet, and gutter connector are mounted by sliding
onto the front gutter bead and then snapping into the rear gutter bead.
When connecting, pay attention to the correct position of seals in outlets, connectors,
and corner pieces, as well as to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets on the gutter connectors, outlets, and 
corner pieces.