Set Rain Gutter 8m Graphite System 100
The BRYZA GUTTER SYSTEM is an established product that was introduced to the market in early 2004.
BRYZA is a complete system consisting of gutters with a semicircular cross-section of 75, 100, and 125, a group of fittings, and downpipes with two diameters of 63 and 90mm.
The discreet elegance of classic forms, easy installation, and a selection
of two colors in various sizes fulfill all customer wishes.
Brown (RAL 8017) - Graphite (RAL 7021)
100 System - SET consists of:
Quantity depending on SET see product image!
- 100 gutter 2m
- 100 gutter end caps (right/left)
- 100 gutter brackets
- 90 downpipe 2m
- 90 pipe socket
- 90 bend 67.5°
- 90 bracket for downpipe
- Spout 100 gutter to 90 downpipe
- 100 gutter connection (from 4m SET)
Gutter System Parts
1. "Gutter" 75, 100, 125mm; 2m
2. "Gutter bracket" 75, 100, 125mm
3. "Inside corner 90°" 75, 100, 125mm
4. "Gutter connector" 75, 100, 125mm
5. "Outside corner 90°" 75, 100, 125mm
6. "Spout" 75/63, 100/63, 100/90, 125/90mm
7. "Gutter end cap right/left" 75, 100, 125mm
8. "Downpipe" 63, 90mm
9. "T-piece" 63, 90mm
10. "Bracket (PVC)" 63, 90mm
11. "Downpipe connection/socket" 63, 90mm
12. "Reduction" 90/63mm
13. "Bend 67.5°" 63, 90mm
14. "Gutter iron (metal) adjustable" 75, 125mm
15. "Hook for PVC bracket" 120, 160, 180, 220, 250, 350mm
16. "Inside corner adjustable angle 120° to 145°" 125mm
17. "Outside corner adjustable angle 120° to 145°" 75, 100, 125mm
Connection Type
The gutters are connected to the pipe fittings by a snap connection.
The connection is sealed with a rubber profile located in the groove of a pipe fitting.
This type of connection allows for easy installation and ensures the required
tightness. The connection of the downpipes with the pipe fittings is done with the connection
sockets without a seal. The mentioned connection types allow for thermal length changes
of the gutter system parts to be compensated.
Please note during installation!
The PVC and steel brackets are mounted directly on the roof battens or rafters.
The bracket distance should be 40-50cm. For proper water drainage, the
gutter should have a slope of 2mm per 1m towards the spout.
Cutting the Gutters and Downpipes
Cut the gutter or downpipe to the correct length with a fine-toothed saw at a right angle.
Gutter Installation in the Brackets and Installation of Spouts and Individual Parts
The installation in the PVC and metal brackets begins with inserting the
gutter bead into the front nose of the bracket, then the inner part of the gutter
is pressed under the rear nose.
Corner piece, spout, and gutter connection piece are mounted by sliding
onto the front bead of the gutter and then snapping into the rear gutter bead.
When connecting, pay attention to the correct position of seals in spouts, connection pieces,
and corner pieces as well as to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets at the gutter connectors, spouts, and
corner pieces.
Corner piece, spout, and gutter connection piece are mounted by sliding
onto the front bead of the gutter and then snapping into the rear gutter bead.
When connecting, pay attention to the correct position of seals in spouts, connection pieces,
and corner pieces as well as to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets at the gutter connectors, spouts, and
corner pieces.
