Gutter Cap Right Brown System 75
The BRYZA GUTTER SYSTEM is an established product that was launched at the beginning of 2004.
BRYZA is a complete system, consisting of gutters with a semi-circular cross-section of 75, 100, and 125,
a group of fittings, and downpipes with two diameters of 63 and 90mm.
The discreet elegance of classic forms, easy installation, and a selection
of two colors in various sizes fulfill all customer wishes.
Brown (RAL 8017) - Graphite (RAL 7021)
75 System
Gutter 75mm with downpipe 63mm.
For small residential buildings, canopies, garages,
balconies, and mansards.
100 System
Gutter 100mm with downpipe 90 or 63mm.
Single-family houses, small and medium-sized warehouses,
commercial and industrial buildings, and
public buildings.
125 System
Gutter 125mm with downpipe 90mm.
Single and multi-family houses, apartment blocks,
warehouses, public buildings, commercial
and industrial buildings.
Gutter System Parts
1. "Gutter" 75, 100, 125mm; 2m
2. "Gutter Bracket" 75, 100, 125mm
3. "Inside Corner 90°" 75, 100, 125mm
4. "Gutter Connector" 75, 100, 125mm
5. "Outside Corner 90°" 75, 100, 125mm
6. "Outlet" 75/63, 100/63, 100/90, 125/90mm
7. "Gutter Cap Right/Left" 75, 100, 125mm
8. "Downpipe" 63, 90mm
9. "T-Piece" 63, 90mm
10. "Clamp (PVC)" 63, 90mm
11. "Downpipe Connector/Sleeve" 63, 90mm
12. "Reduction" 90/63mm
13. "Bend 67.5°" 63, 90mm
14. "Adjustable Gutter Bracket (Metal)" 75, 125mm
15. "Hook for PVC Clamp" 120, 160, 180, 220, 250, 350mm
16. "Inside Corner Adjustable Angle 120° to 145°" 125mm
17. "Outside Corner Adjustable Angle 120° to 145°" 75, 100, 125mm
Connection Type
The gutters are connected to the pipe fittings using a snap connection.
The connection is sealed with a rubber profile located in the groove of a pipe fitting.
This type of connection allows for easy installation and ensures the required
tightness. The connection of the downpipes with the pipe fittings is done with
connection sleeves without seals. The mentioned connection types allow
thermal length changes of the gutter system parts to be compensated.
Please Note During Installation!
The PVC and steel brackets are mounted directly on the roof battens or rafters.
The bracket spacing should be 40-50cm. For proper water drainage, the
gutter should have a slope of 2mm per 1m towards the outlet.
Cutting the Gutters and Downpipes
Cut the gutter or downpipe to the correct length with a fine-toothed saw at a right angle.
Gutter Installation in the Brackets and Installation of Outlets and Parts
The installation in the PVC and metal brackets begins with inserting the
gutter bead into the front nose of the bracket, then pressing the inner part
of the gutter under the rear nose.
Corner piece, outlet, and gutter connector are mounted by sliding
onto the front bead of the gutter and then snapping into the rear gutter bead.
When connecting, pay attention to the correct position of seals in outlets, connectors,
and corner pieces, as well as to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets at the gutter connectors, outlets, and
corner pieces.
Corner piece, outlet, and gutter connector are mounted by sliding
onto the front bead of the gutter and then snapping into the rear gutter bead.
When connecting, pay attention to the correct position of seals in outlets, connectors,
and corner pieces, as well as to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets at the gutter connectors, outlets, and
corner pieces.
