Set Gutter 4m brown System 75
The BRYZA GUTTER SYSTEM is an established product that was launched at the beginning of 2004.
BRYZA is a complete system,
consisting of gutters with a semicircular cross-section of 75, 100, and 125, a group of fittings, and downpipes with two diameters of 63 and 90mm.
The discreet elegance of classic shapes, easy installation, and a choice
of two colors in different sizes fulfill all customer wishes.
Brown (RAL 8017) - Graphite (RAL 7021)
75 System - SET consists of:
Quantity according to SET see product image!
- 75 gutter 2m
- 75 gutter end caps (right/left)
- 75 gutter brackets
- 63 downpipe 2m
- 63 pipe socket
- 63 bend 67.5°
- 63 bracket for downpipe
- Outlet 75 gutter to 63 downpipe
- 75 gutter connection (from 4m SET)
Gutter system parts
1. "Gutter" 75, 100, 125mm; 2m
2. "Gutter bracket" 75, 100, 125mm
3. "Internal corner 90°" 75, 100, 125mm
4. "Gutter connector" 75, 100, 125mm
5. "External corner 90°" 75, 100, 125mm
6. "Outlet" 75/63, 100/63, 100/90, 125/90mm
7. "Gutter end cap right/left" 75, 100, 125mm
8. "Downpipe" 63, 90mm
9. "T-piece" 63, 90mm
10. "Bracket (PVC)" 63, 90mm
11. "Downpipe connection/socket" 63, 90mm
12. "Reduction" 90/63mm
13. "Bend 67.5°" 63, 90mm
14. "Gutter iron (metal) adjustable" 75, 125mm
15. "Hook for PVC bracket" 120, 160, 180, 220, 250, 350mm
16. "Internal corner adjustable angle 120° to 145°" 125mm
17. "External corner adjustable angle 120° to 145°" 75, 100, 125mm
Connection type
The gutters are connected to the pipe fittings by a snap connection.
The connection is sealed with a rubber profile located in the groove of a pipe fitting.
This type of connection allows for easy installation and ensures the required
tightness. The connection of the downpipes with the pipe fittings is made with the connection
sockets without a seal. The mentioned connection types allow for thermal length changes
of the gutter system parts to be compensated.
Please note during installation!
The PVC and steel brackets are mounted directly on the roof battens or rafters.
The bracket spacing should be 40-50cm. For proper water drainage, the
gutter should have a slope of 2mm per 1m towards the outlet.
Cutting the gutters and downpipes
Cut the gutter or downpipe to the correct length with a fine-toothed saw at a right angle.
Gutter installation in the brackets and installation of outlets and individual parts
The installation in the PVC and metal brackets begins with inserting the
gutter bead into the front nose of the bracket, then the inner part of the gutter
is pressed under the rear nose.
Corner piece, outlet, and gutter connection piece are mounted by sliding
onto the front bead of the gutter and then snapping into place on the rear gutter bead.
When connecting, make sure the seals in outlets, connection pieces,
and corner pieces are in the correct position and pay attention to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets on the gutter connectors, outlets, and
corner pieces.
Corner piece, outlet, and gutter connection piece are mounted by sliding
onto the front bead of the gutter and then snapping into place on the rear gutter bead.
When connecting, make sure the seals in outlets, connection pieces,
and corner pieces are in the correct position and pay attention to the limiters on the inner surface of these parts.
It is recommended to install additional gutter brackets on the gutter connectors, outlets, and
corner pieces.
